Kia Sportage: Roof Trim: Repair procedures - Interior - Body (Interior and Exterior) - Kia Sportage SL Service & Repair ManualKia Sportage: Roof Trim: Repair procedures

Third generation SL (2010–2016) / Kia Sportage SL Service & Repair Manual / Body (Interior and Exterior) / Interior / Roof Trim: Repair procedures

Replacement
Sunvisor Replacement
   
Use a plastic panel removal tool to remove interior trip pieces to without marring the surface.
Put on gloves to protect your hands.
1.
After loosening the mounting screws, then remove the sunvisor (A) and retainer (B).

2.
Installation is the reverse of removal.
Assist Handle Replacement
   
Use a plastic panel removal tool to remove interior trip pieces to without marring the surface.
Put on gloves to protect your hands.
1.
Remove the covers (A).
2.
After loosening the mounting screws, then remove the assist handle (B).

3.
Installation is the reverse of removal.
Overhead Console Replacement
   
Use a plastic panel removal tool to remove interior trip pieces to without marring the surface.
Put on gloves to protect your hands.
1.
After loosening the mounting screws, then remove the overhead console assembly (A).

2.
Disconnect the connectors (A).

3.
Installation is the reverse of removal.
   
Make sure the connector is connected properly.
Room Lamp Replacement
   
Use a plastic panel removal tool to remove interior trip pieces to without marring the surface.
Put on gloves to protect your hands.
1.
Using a screwdriver or remover, remove the room lamp cover (B).
2.
After loosening the mounting screws, then remove the room lamp (A).

3.
Disconnect the connector (A).

4.
Installation is the reverse of removal.
   
Make sure the connectors are plugged in properly.
Vanity Lamp Replacement
   
Use a plastic panel removal tool to remove interior trip pieces to without marring the surface.
Put on gloves to protect your hands.
1.
Using a screwdriver or remover, remove the vanity lamp (A).
2.
Disconnect the connector (B).

3.
Installation is the reverse of removal.
   
Make sure the connector is connected properly.
Roof Trim Replacement
   
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
Put on gloves to protect your hands.
1.
Remove the following items.
Front seat
(Refer to the BD group - "Front Seat")
Rear seat
(Refer to the BD group - "Rear Seat")
Sunvisor
Overhead console
Room lamp
Assist handle
Front pillar trim
(Refer to the BD group - " Interior Trim")
Front door scuff trim & Rear door scuff trim
(Refer to the BD group - " Interior Trim")
Center pillar lower trim & Center pillar upper trim
(Refer to the BD group - " Interior Trim")
Rear pillar trim
(Refer to the BD group - " Interior Trim")
2.
Remove the ECM mirror cover (A).
3.
Disconnect the ECM mirror connector (B).

4.
Remove the rain sensor cover (A).
5.
Disconnect the rain sensor connector (B).

6.
Disconnect the roof trim main connector (A).
[Driver''s]

[Passenger''s]

7.
Disconnect the antenna connector (A).

8.
Remove the clips and roof trim (A).

9.
Installation is the reverse of removal.
   
Make sure the connectors are plugged in properly.
Replace any damage clips.
Roof Trim: Components and Components Location
Components 1. Roof trim2. Sunvisor [Driver''s]3. Sunvisor [Passenger''s] Components [Panoramaroof] 1. Roof trim2. Sunvisor [Driver''s]3. Sunvisor [Passenger''s] ...

Interior Trim: Components and Components Location
Components 1. Front pillar trim2. Center pillar upper trim3. Center pillar lower trim4. Luggage side trim5. Cowl side trim6. Front door scuff trim7. Rear door scuff trim8. Front step trim9. Rear ...

Other Information:

Positive Crankcase Ventilation (PCV) Valve: Repair procedures
Removal 1. Disconnect the vapor hose (A). 2. Remove the PCV valve (B). Inspection 1. Insert a thin stick (A) into the PCV valve (B) from the threaded side to check that the plunger move ...

Heated Oxygen Sensor (HO2S): Repair procedures
Inspection 1. Turn the ignition switch OFF. 2. Disconnect the HO2S connector. 3. Measure resistance between the HO2S terminals 4 and 5 [B1/S1]. 4. Measure resistance between the HO2S t ...

Categories


Copyright © www.kispmanual.com 2014-2024