Kia Sportage: Windshield Glass: Repair procedures

Third generation SL (2010–2016) / Kia Sportage SL Service & Repair Manual / Body (Interior and Exterior) / Interior / Windshield Glass: Repair procedures

Replacement

Removal

•	Put on gloves to protect your hands.

•	Use seat covers to avoid damaging any surfaces.

Remove the following items.

•	Front pillar trim (Refer to the BD group – “Interior Trim”)

•	Inside rearview mirror (Refer to the BD group – “Mirror”)

•	Rain sensor (Refer to the BE group – “Rain Sensor”)

•	Wiper arm (Refer to the BD group – “Cowl Top Cover”)

•	Cowl top cover (Refer to the BD group – “Cowl Top Cover”)

•	Windshield glass deicer connector (Refer to the BE group – “Windshield Deicer”)

2.	Using a screwdriver or remover, remove the windshield side moulding (A).

3.	Cut out the sealant using the sealant cutting tool(A)(09861-31100).

4.	Remove the windshield glass (B) carefully using the glass holder (A).

Installation

With a knife, scrape the old adhesive smooth to a thickness of about 2mm (0.08 in.) on the bonding surface around the entire windshield opening flange:

•	Do not scrape down to the painted surface of the body; damaged paint will interfere with proper bonding.

•	Remove the rubber dam and fastereners from the body.

•	Mask off surrounding surfaces before painting

2.	Clean the bonding surface with a sponge dampened in alcohol. After cleaning, keep oil, grease and water from getting on the clean surface.

3.	Install the windshield side moulding (A) and fasteners. Do not allow any gaps.

4.	Install the spacer (A) install the windshield glass (B) temporarily with marking sure to position them on the center, and then place the alignment mark (C).

With a sponge, apply a light coat of body primer to the original adhesive remaining around the windshield opening flange. Let the body primer dry for at least 10 minutes.

•	Do not apply glass primer to the body, and be careful not to mix up glass and body primer sponges.

•	Never touch the primed surfaces with your hands.

•	Mask off the dashboard before painting the flange.

Apply a light coat of glass primer to the outside of the fasteners.

•	Never touch the primed surface with your hand If you do, the adhesive may not bond to the glass properly, causing a leak after the windshield glass is installed.

•	Do not apply body primer to the glass.

•	Keep water, dust, and abrasive materials away from the primer.

Pack adhesive into the cartridge without air pockets to ensure continuous delivery. Put the cartridge in a caulking gun, and run a bead of adhesive (B) around the edge of the windshield (A) between the fastener and moulding as shown. Apply the adhesive within 30 minutes after applying the glass primer.

Make a slightly thicker bead at each corner.

Use suction cups (A) to hold the windshield (B) over the opening, align it with the alignment marks (C) made in step 15, and set it down on the adhesive. Lightly push on the windshield until its edges are fully seated on the adhesive all the way around. Do not open or close the doors until the adhesive is dry.

9.	Scrape or wipe the excess adhesive off with a putty knife or towel. To remove adhesive from a painted surface or the windshield, wipe with a soft shop towel dampened with alcohol.

10.

Let the adhesive dry for at least one hour, then spray water over the windshield and check for leaks. Make leaking areas, and let the windshield dry, then seal with sealant:

•	Let the vehicle stand for at least four hours after windshield installation. If the vehicle has to be used within the first four, it must be driven slowly.

•	Keep the windshield dry for the first hour after installation.

11.

Reinstall all remaining removed parts. Install the rearview mirror after the adhesive has dried thoroughly. Advise the customer not to do the following things for two the three days:

•	Slam the door with all the windows rolled up.

•	Twist the body excessively (such as when going in and out of driveways at an angle or driving over rough, uneven roads)

12.

Installation the following items.

•	Windshield glass deicer connector (Refer to the BE group – “Windshield Deicer”)

•	Cowl top cover (Refer to the BD group – “Cowl Top Cover”)

•	Wiper arm (Refer to the BD group – “Cowl Top Cover”)

•	Rain sensor (Refer to the BE group – “Rain Sensor”)

•	Inside rearview mirror (Refer to the BD group – “Mirror”)

•	Front pillar trim (Refer to the BD group – “Interior Trim”)

Windshield Glass: Components and Components Location

Components 1. Windshield side moulding2. Windshield glass ...

Bumper

...

Other Information:

Description and Operation
OBD-II review 1. Overview The California Air Resources Board (CARB) began regulation of On Board Diagnostics (OBD) for vehicles sold in California beginning with the 1988 model year. The first ...

Front Driveshaft: Repair procedures
Replacement 1. Loosen the wheel nuts slightly. Raise the vehicle, and make sure it is securely supported. 2. Remove the front wheel and tire (A) from front hub. Tightening torque : 88.3 ~ ...

Kia Sportage: Windshield Glass: Repair procedures

Windshield Glass: Components and Components Location

Bumper

Other Information:

Categories