Kia Optima Manuals

Kia Sportage: Transfer Fluid: Repair procedures - Transfer Assembly - 4 Wheel Drive (4WD) System - Kia Sportage SL Service & Repair ManualKia Sportage: Transfer Fluid: Repair procedures

Third generation SL (2010–2016) / Kia Sportage SL Service & Repair Manual / 4 Wheel Drive (4WD) System / Transfer Assembly / Transfer Fluid: Repair procedures

Inspection
   
•
Transfer oil should be inspected and refilled every 60000 km (40000 mile) / 4 year.
1.
Remove the under cover (A).

2.
Remove the oil filler plug (A).

3.
Check the oil level.
   
Oil level must be up to fill the hole, if not, add oil until it runs over.

4.
Install the oil filler plug with new gasket.
Tightening torque :
39.2 ~ 58.8 N.m (4.0 ~ 6.0 kgf.m, 28.9 ~ 43.4 lb-ft)
5.
Install the under cover.
Tightening torque:
19.6 ~ 24.5 N.m (2.0 ~ 2.5 kgf.m, 14.5 ~ 18.1 lb-ft
Replacement
   
Change 
Normal Use
Severe Use
No service required
120,000 km
(80,000 miles)

Severe driving conditions
1)
Driving in dusty, rough roads
2)
Drivng in mountains areas
3)
Driving for patrol car, taxi, commercial car or vehicle towing
4)
Driving over 170Km/h
* Transfer oil should be replaced if the transfer assembly is fall into the water.
1.
Remove the under cover (A).

2.
Drain the transfer oil after loosening the drain plug (A).

3.
Install the drain plug with new gasket.
Tightening torque :
58.9 ~ 78.5 N.m (6.0 ~ 8.0 kgf.m, 43.4 ~ 57.9 lb-ft)
4.
Remove the oil filler plug (A).

5.
Add new oil through the filler plug hole.
Standard oil :
SAE 75W/90 API GL-5
Oil capacity :
0.6 L(0.16 U.S.gal., 0.63 U.S.qt, 0.53 Imp.qt.)
   
•
Filled up to lower filler plug thread level.

6.
Install the oil filler plug with new gasket.
Tightening torque :
39.2 ~ 58.8 N.m (4.0 ~ 6.0 kgf.m, 28.9 ~ 43.4 lb-ft)
7.
Install the under cover.
Tightening torque :
19.6 ~ 24.5 N.m (2.0 ~ 2.5 kgf.m, 14.5 ~ 18.1 lb-ft)
Transfer Assembly
...

Front Wheel Transfer Assembly: Components and Components Location
Components Location 1. Automatic transaxle2. Transfer assembly3. Propeller shaft4. Coupling assembly5. Differential assembly ...

Other Information:

Heated Oxygen Sensor (HO2S): Specifications
Specification HO2S [Bank 1/Sensor 1] ItemSpecificationHeater Resistance (?)2.5 ~ 4.0 [20°C(68°F)] HO2S [Bank 1/Sensor 2] A/F Ratio (?)Output Voltage(V)RICHApprox. 0.9LEANApprox. 0.04 ...

Troubleshooting
Engine Overheat Troubleshooting Inspection RemedyVisual inspectionInspect for shortage of coolant in reservoir tank .Reinspect after replenishing coolant.Inspect for coolant pollution after remo ...

Categories


Copyright © www.kispmanual.com 2014-2024