Kia Sportage: Front Seat Belt: Repair procedures - Seat Belt - Body (Interior and Exterior) - Kia Sportage SL Service & Repair ManualKia Sportage: Front Seat Belt: Repair procedures

Third generation SL (2010–2016) / Kia Sportage SL Service & Repair Manual / Body (Interior and Exterior) / Seat Belt / Front Seat Belt: Repair procedures

Replacement
Front Seat Belt Replacement
   
When installing the belt, make sure not to damaged the pretensioner.
1.
Remove the following items first :
Front seat assembly
(Refer to the BD group - "Front Seat")
Front door scuff trim & Rear door scuff trim
(Refer to the BD group - "Interior Trim")
2.
To remove the seat belt anchor pretensioner (C), keep on pushing the lock pins (A) as arrow direction.
And then remove the seat belt after pushing the lock pin (B).

3.
Remove the center pillar lower trim (A).

4.
After loosening the mounting bolt, then remove the center pillar upper trim (A) .

5.
After loosening the mounting bolt, then remove the front seat belt upper anchor (A).

Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft )

6.
After disconnecting the pretensioner connector lock pin, remove the SIS connector (A), loosen the mounting bolt, then remove the pretensioner (B).

Tightening torque :
39.2~53.9 N.m (4.0~5.5 kgf.m, 28.9~39.8 lb-ft)

7.
Installation is the reverse of removal.
Height Adjust Replacement
1.
Remove the following items first :
Front seat assembly
(Refer to the BD group – “Front Seat”).
Front door scuff trim & Rear door scuff trim
(Refer to the BD group - "Interior Trim")
Front seat belt lower anchor
Center pillar lower trim
(Refer to the BD group - "Interior Trim")
Center pillar upper trim
(Refer to the BD group - "Interior Trim")
Front seat belt upper anchor
2.
After loosening the bolts, then remove the height adjustor (A).

Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft)

3.
Installation is the reverse of removal.
   
Replace ant damaged clips.
Make sure the height adjust properly.
Front Seat Belt Buckle Replacement
1.
Remove the following items first :
Front seat assembly
(Refer to the BD group - "Front Seat")
2.
After loosening the mounting bolt, then remove the front seat belt buckle (A).

Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.9 ~ 39.8 lb-ft)

3.
Installation is the reverse of removal.
Components and Components Location
Components 1. Front seat belt2. Height adjuster3. Rear seat belt4. Rear seat belt [Center]5. Rear seat belt buckle ...

Rear Seat Belt: Repair procedures
Replacement Rear Seat Belt Replacement     • When installing the belt, make sure not to damaged the retractor. 1. Remove the following items first. • ...

Other Information:

Instrument Cluster: Schematic Diagrams
Circuit Diagram (1) Circuit Diagram (2) CLU1 message signal flow (B > C CAN gateway) CLU2 message signal flow (B > C CAN gateway) CLU message 1 signal flow (C > B CAN gateway) CLU message 3 signa ...

Heater & A/C Control Unit(Manual): Components and Components Location
Components Connector Pin Function ConnectorPin NoFunctionConnectorPin NOFunctionConnector(A)1HighConnector(B)1Tail Lamp (ILL+)2Middle High2Battery3Middle Low3Mode Actuator (VENT)4-4Mode Actuator ...

Categories


Copyright © www.kispmanual.com 2014-2024