Kia Sportage: Radiator: Repair procedures

Third generation SL (2010–2016) / Kia Sportage SL Service & Repair Manual / Engine Mechanical System / Cooling System / Radiator: Repair procedures

Inspection

Radiator Cap Testing

1.	Remove the radiator cap, wet its seal with engine coolant, and then install it on a pressure tester.

2.	Apply a pressure of 93.16 ~ 122.58kPa (0.95 ~ 1.25kgf/cm?, 13.51 ~ 17.78psi).

3.	Check for a drop in pressure.

4.	If the pressure drops, replace the cap.

Radiator Leakage Test

1.	Wait until engine is cool, then carefully remove the radiator cap and fill the radiator with engine coolant, then install it on the pressure tester (A).

2.	Apply a pressure tester to the radiator and apply a pressure of 93.16 ~ 122.58kPa (0.95 ~ 1.25kgf/cm?, 13.51 ~ 17.78psi).

3.	Inspect for engine coolant leaks and a drop in pressure.

Remove the tester and reinstall the radiator cap.

Check for engine oil in the coolant and/or coolant in the engine oil.

Removal and Installation

1.	Disconnect the battery terminals. (Refer to Engine and transaxle assembly in this group)

2.	Remove the air cleaner assembly and intercooler inlet/outlet hose & pipes. (Refer to Engine and transaxle assembly in this group)

3.	Remove the battery and battery tray. (Refer to Engine and transaxle assembly in this group)

4.	Remove the radiator grill upper guard (A). (Refer to BD group)

5.	Remove the radiator upper cover (A).

6.	Remove the horn bracket (A). (Refer to BE group)

7.	Remove the radiator front air guard (B).

8.	Seperate the condenser (C) from the radiator.

9.	Disconnect the over flow hose (A) from the radiator.

10.

Remove the radiator mounting bracket assemblies (A).

Tightening torque :

8.8 ~ 10.8 N.m (0.9 ~ 1.1 kgf.m, 6.5 ~ 8.0 lb-ft)

11.	Disconnect the fan motor connector (A).

12.

Remove the cooling fan assembly (A).

Tightening torque :

4.9 ~ 7.8 N.m (0.5 ~ 0.8 kgf.m, 3.6 ~ 5.8 lb-ft)

13.	Remove the under cover. (Refer to Engine and transaxle assembly in this group)

14.	Loosen the drain plug, and drain the engine coolant. Remove the radiator cap to drain with speed.

15.	Disconnect the radiator upper hose (A) and lower hose (B).

16.	Disconnect the ATF cooler hoses. (Refer to AT group)

17.	Remove the radiator assembly (A).

18.	Installation is the reverse order of removal.

19.

Fill the radiator with coolant and check for leaks.

•	Bleed air from the cooling system.

–	Start engine and let it run until it warms up. (Until the radiator fan operates 3 or 4 times.)

–	Turn off engine. Check the coolant level and add coolant if needed. This will allow trapped air to be removed from the cooling system.

–	Put the radiator cap on tightly, then run engine again and check for leaks.

Radiator: Components and Components Location

Components 1. Cooling fan assembly2. Radiator assembly3. Mounting insulator4. Radiator mounting bracket5. Radiator upper hose6. Radiator lower hose7. Reservoir tank8. Over flow hose9. ATF ...

Water pump: Components and Components Location

Components 1. Water pump pulley2. Water pump sub assembly3. Water pump gasket4. Water pump cover5. Water pump cover gasket6. O-ring7. Water inlet pipe8. Water temperature control assembly9. ...

Other Information:

Cylinder Block: Components and Components Location
Components 1. Piston ring2. Snap ring3. Piston4. Connecting rod 5. Connecting rod upper bearing6. Piston pin7. Connecting rod lower bearing8. Connecting rod bearing cap9. Ladder frame10. Oil filt ...

SS-B Solenoid Valve(ON/OFF): Specifications
Specifications ON/OFF Solenoid Valve(SS-B) ? Control type : Normal low type Control pressure kpa (kgf/cm?, psi)490.33(5.0, 71.12) Internal resistance(?)10 ~ 11 ...

Kia Sportage: Radiator: Repair procedures

Radiator: Components and Components Location

Water pump: Components and Components Location

Other Information:

Categories